You are here: Products / Software / Tracii 400 Software / FAQ/Support

¬Social Bookmarks

Products

1: Hardware.
- 1.1: I2C Product Comparison.
- 1.2: Connii MM 2.0.
- 1.3: Tracii XL 2.0.
- 1.4: Tracii XL.
- 1.5: I2C Negative Tester.
- 1.6: Tracii 400.
- 1.7: Levii.
- 1.8: Optii.
- 1.10: telos SPI Master.
- 1.11: telos ABIC 2 Analyser.
- 1.12: CANdice.
- 1.14: Accessories.
- 1.15: Expired.
2: Software.
- 2.1: I2C Studio.
- 2.2: I2C Framework.
- 2.3: I2C Flasher.
- 2.4: Tracii 400 Software.
  - 2.4.1: TraciiTalk.
  - 2.4.2: TraciiSpy.
  - 2.4.3: TraciiWork.
  - 2.4.4: TraciiLabview.
  - 2.4.5: FAQ/Support.
- 2.5: .
3: Support Policy.

Here you can obtain answers to the most frequently asked questions. If you have a question that is not covered in the FAQ, please fill out the feedback form.

Search the list

Please enter a searchword.

List of all articles

Dynamically Switching Operating Modes Friday 06. June 2003 Age: 9 yrs
I have a system in which I have two or more i�C-bus devices - one of them is a Tracii application. I want to run Tracii in master mode, however my slave device needs to initiate the communication from time to time. Additionally I want to run Tracii in slave mode, but Tracii should also initiate commu... [more] 06.06.03 18:15 Category: Tracii 400 - Fast Mode I2C Monitor and Interface

Which modes can Tracii have at one time? Friday 06. June 2003 Age: 9 yrs
All the modes are exklusive i.e. Tracii can either be master, slave or tracer. Switching between modes is possible using TraciiWork. Since changing modes takes some time it is not recommended to frequently switch Tracii in one application. [more] 06.06.03 18:13 Category: Tracii 400 - Fast Mode I2C Monitor and Interface

TraciiSpy shows error "Tracii-Board not found" Friday 06. June 2003 Age: 9 yrs
Please verify correct jumper settings LED Pwr is on LED ConfOK comes up shortly after pressing the RESET button printer mode configuration supply voltage too low last not least: quality of power supply cable is connected 1:1 and is not longer than ... [more] 06.06.03 18:10 Category: Tracii 400 - Fast Mode I2C Monitor and Interface

I need a different I2C termination Friday 06. June 2003 Age: 9 yrs
Tracii 400 has several I2C terminations available. With the help of jumper JP4 values of 4k7, 8k2 and 15k can be selected. Any parallel combination of them is possible either. Moreover it is possible to disable the termination at all. The termination values are printed on-board. [more] 06.06.03 18:09 Category: Tracii 400 - Fast Mode I2C Monitor and Interface

I2C device does not answer Friday 06. June 2003 Age: 9 yrs
I2C addresses can be notified with 7 or 8 bits. The Tracii software provides the option use I2C-bus device addresses in 7 and 8 bit notation. I.e. the least significant bit of the first I2C-bus message - the read or write bit - is no part of the address. In Tracii Talk the R/W bit will be... [more] 06.06.03 18:08 Category: Tracii 400 - Fast Mode I2C Monitor and Interface

What is the resolution for time stamps? Friday 06. June 2003 Age: 9 yrs
It depends. Tracii offers high resolution for smaller periods but is able to process longer periods too. Thus, the resolution depends on the actual transmission time of the data bytes. The below table shows the transmission time of the databytes and the resolution time stamps are offering. transm... [more] 06.06.03 18:05 Category: Tracii 400 - Fast Mode I2C Monitor and Interface

Tracii is not recognized by the software! Friday 06. June 2003 Age: 9 yrs
Tracii supports the bidirectional EPP mode whilst ECP is not supported. Please check the documentation of your computer or BIOS on instructions how to set your parallel port to EPP mode. In case your PC does not feature EPP mode, we can offer a simple EPP interface card. Usually... [more] 06.06.03 18:02 Category: Tracii 400 - Fast Mode I2C Monitor and Interface

< Previous Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Next >