Here you can obtain answers to the most frequently asked questions. If you have a question that is not covered in the FAQ, please fill out the feedback form.
Search the list
|
List of all articles
| TraciiTalk: More than 400 kbit/s Monday 25. October 2004 Age: 6 yrs | ||
|
TraciiTalk limits the maximal transfer speed to 400 kbit/s, which - according to the I2C specification - is the maximum rate for fast mode. Nevertheless Tracii 400 is able to drive buses with up to 800 kbit/s. To have this set in our TraciiTalk application press ctrl-shift-pageup/pagedown in the bi... [more]25.10.04 12:58 Category: Tracii 400 - Fast Mode I2C Monitor and Interface |
 |
|
|
||
| Tip: Tracii 400 can supply power to other i2c devices Wednesday 04. August 2004 Age: 6 yrs | ||
|
Application note - Drawing 5v regulated power from Tracii400 [more]04.08.04 13:18 Category: Tracii 400 - Fast Mode I2C Monitor and Interface |
|
|
|
||
| Tracii 400 reads SPI-Devices Tuesday 03. August 2004 Age: 6 yrs | ||
AbstractEven though Tracii 400 is primarily designed to serve as an I2C interface it can be used to access other bus systems as well. This application note shows how to use the input and output test pins to read values from an SPI device. TheoryTracii 400 is equipped with two... [more]03.08.04 15:50 Category: Tracii 400 - Fast Mode I2C Monitor and Interface |
|
|
|
||
| Addressing internal address space of Tracii in a slave mode Monday 21. June 2004 Age: 6 yrs | ||
|
I wonder whether there is a way to send several transactions to different locations in the Tracii internal buffer? If there is, is it possible to read it back from a specific location? I would like to simulate a situation when a master sets different registers of a slave and then performs read-modif... [more]21.06.04 16:33 Category: Tracii 400 - Fast Mode I2C Monitor and Interface |
|
|
|
||
| Tracii 400 is recognized by TraciiTalk but not by TraciiSpy Wednesday 26. May 2004 Age: 6 yrs | ||
|
Tracii 400 is recognized by TraciiTalk but not by TraciiSpy. The license file should be in the right place. Can anybody help me? Tracii Spy recognizes Tracii 400 independently if a License File was found or not. Please check if the LPT port was set correctly in the “General Options” dialog... [more]26.05.04 09:16 Category: Tracii 400 - Fast Mode I2C Monitor and Interface |
|
|
|
||
| Talk: 10 bit addresses and repeated start conditions Tuesday 11. May 2004 Age: 6 yrs | ||
|
When I use Tracii 400 in Slave Mode I don´t get an acknowledge for the address after the repeated start condition: S - [10BitAddr1]w A - [10BitAddr2] A - [Data1]A...[DataN]A - S - [10BitAddr1]r NA - [Data1]NA...[DataN]NA - P What can I do? Due to a bug in the firmware Tracii 400 does not acknowled... [more]11.05.04 15:00 Category: Tracii 400 - Fast Mode I2C Monitor and Interface |
|
|
|
||
| Double NACK for XFP Wednesday 07. January 2004 Age: 7 yrs | ||
|
I am using Tracii board as a master to a device in slave mode. According to the I2C specifications, at the end of a simple read operation, the master sends a NACK, followed by a STOP condition. However, the device we are developing follows a special specification k... [more]07.01.04 19:04 Category: Tracii 400 - Fast Mode I2C Monitor and Interface |
|
|
|
||